浅谈碳化木吊顶怎样安装的步骤

浅谈碳化木吊顶怎样安装的步骤

Discussion on how to install the ceiling of carbonized wood

螺柱，铅笔，粉笔线，斜切锯，阶梯，防腐木板，建筑胶，气动钉枪，曲线锯，台锯。

Stud, pencil, chalk line, miter saw, ladder, anticorrosive wood, building glue, pneumatic nail gun, curve saw, table saw.

毕节防腐木小编今天就讲讲碳化木厂家吊顶施工工艺步骤

Bijie anticorrosion wood small editor today talks about the construction process of the hanging roof of the carbonized wood factory

1、使用螺柱发现者定位在吊顶龙骨。搁栅用铅笔标记和捕捉每行用粉笔线。这将使搁栅容易看到的位置。只要有可能，木板安装在吊顶龙骨垂直。这会使碳化木吊顶更强。

1. The stud found in the stud is located in the ceiling keel. The grille marks and captures the chalk lines for each line with a pencil. This will make the grid easy to see. As long as it is possible, the plank is installed vertically on the ceiling keel. This will make the sling of carburized wood stronger.

2、测量的长度的上限。这将有助于多久，你的每一个天花板的碳化木板需要给你一个好主意。由于您使用的舌和凹槽的碳化木板，你将需要切断的栈道从侧面将对接在墙上的舌头。使用斜切锯切割碳化木板的两端。

2. The upper limit of the length of the measurement. How long it will help, you need a good idea for each ceiling carbonized board. As you use the tongues and grooves of the carbonized wood, you will need to cut off the trestle from the side and butt the tongue on the wall. Both ends of saw cutting boards are used carbide chamfered.

3、胎圈的结构粘合剂应用到后面的第一个要安装的碳化木板。站在梯子上，碳化木板推到旁边的墙壁。小心地拉碳化木板下来，然后再向上推入到位。这将有助于结构粘合剂均匀传播到后面的栈道。使用气动枪钉碳化木板钉成吊顶龙骨。

3, the structural adhesive of the bead is applied to the first carbonated wood board to be installed. Stand on the ladder, and the carburized wood is pushed to the wall next to it. Carefully pull the carbonized board down and then push it up. This will help the structural adhesives spread evenly to the rear trestle. A pneumatic gun is used to nail the carburized board into a ceiling keel.

4、以同样的方式，您安装第一个碳化木板，安装所有的木板。然而，随着连续木板，你需要确保你把舌头伸进槽上木板。这将加强木板。正如你临到灯具和天花板障碍物的测量和标记的木板，并用夹具锯切大小的防腐木吊顶。

4. In the same way, you install the first carbonized board and install all the boards.  However, with the continuous board, you need to make sure that you put your tongue into the slots. This will strengthen the board. Just as you go to the board of measuring and marking the lamps and ceiling obstacles and sawing the size of the anticorrosion wood ceiling with the jig.

5、测量并切割碳化木板的最后一行。最有可能在最后一行的木板小于整个的木板。测量板的空间大小和撕裂的木板桌子上看到的。您将需要削减唇沟的底部，从上板，使最后的碳化木板容易下降，即使在狭小的空间。

5, measure and cut the last line of the carburized board. The most likely board in the last row is less than the whole board. Measure the size of the plate and tear the tearing board on the table. You will need to cut the bottom of the lip groove from the upper plate so that the last carbonized wood is easy to drop, even in a narrow space.

毕节防腐木小编今天就分享到这里了。

Bijie preservative wood little editor is here today.